Drawer Depot - Custom Made Drawer Boxes
WEBCustom-made Dovetail Drawer Boxes , Pre-Made Drawer Box, BLUM Metabox, BLUM Legrabox, Pantry Drawer Box, Cabinet Doors and Drawer Fronts, and Cabinet Hardware.
WEBMOUNT TO CABINET FLOOR, SHELF SURFACE ITEM# SIZE 950SSL600 24” - DT600mm x CT600mm 950SSL550 22” - DT550mm x CT550mm 950SSL500 20” - DT500mm x CT500mm 950SSL450 18” - DT450mm x CT450mm 950SSL400 16” - DT400mm x CT400mm 950SSL350 14” - DT350mm x CT350mm 950SSL300 12” - DT300mm x CT300mm 950SSL250 10” - DT250mm x CT250mm
The Drawer Depot : Shipping Calculator
WEBThe Drawer Depot : Shipping Calculator
WEBAdditional stabilization for wide drawers For use with METABOX 330M and H series full extension drawers only. Available for drawer lengths 550mm (22") Linkage rod can be cut according to cabinet width. Suitable for cabinet widths up to 1 00mm (47"). Simple assembly of all components. Does not increase load capacity. ZST.550MH 550 (22") drawer ...
WEBcabinet profiles when used in an interior roll-out application ÁCan be used with all 562H, 568H and 568. series runners Part no. Right end cap Left end cap %SBXFS GSPOU BEKVTUFS Nylon housing with pre-mounted 8-32 steel nut. For four-sided drawers. Adjusts height and side-to-side by (3/16"). /05& See next page for marking guage
WEBcabinets. Not necessary for panel cabinet installation. Using TANDEM page 13 Drawer preparation page 14 - Two required per drawer - Depth and side-to-side self-alignment - Zinc-plated steel Inset drawer pg. 27 Narrow drawerpg. 29 Roll-out tray pg. 31 Bottom mount pg. 32 ORGA-LINE pg. 35 Deep drawer pg. 39
WEBcabinet using the locator pins, attach the mechanism with the five mounting screws provided (5) wood screws 1 Locating pin locations and minimum depth Part no. 65.5020 2 Attaching the lift mechanism #7x35 mm Face frame Panel NOTE: Face frame cabinets must be blocked out flush with the frame. 88 min 225 min 278 min 56 37 192 88 5 min 225 min 7 8 ...
WEBusing tandem qbhf drawer preparation qbhf accessories qbhf assembly aids qbhf 4uboebse mpdljoh efwjdf Á0of sjhiu boe pof mfgu sfrvjsfe qfs esbxfs Á.jojnvn joufsjps esbxfs xjeui Á)fjhiu bekvtubcmf /05& 4ff qbhf gps puifs pqujpot 1bsu op 3jhiu mpdljoh efwjdf5 3
WEBCabinet Member 1. Attach brackets to slide at desired height and position (inboardor outboard) using self-tapping screws. Cabinet member to be mounted parallel to shelf/drawer sides. 2. Position slide so the front of the cabinet member is 1/8" [3.2] behind the shelf/drawer front when the drawer is in the closed position. 3.
WEBDeduct from inside cabinet width 10 (3/8") 12 (15/32")14 (9/16") 16 (5/8") 18 (23/32") Positive stop locking T51.1700.PO device for roll-out applications Dimensions in millimeters (inch equivalents as noted) Installation screws Positive stop locking device - One right and one left required per drawer - For interior roll out applications
Skip to content